MODEL

PLN-45-12

OUTPUT

DCVOLTAGE

12V

CONSTANT CURRENT REGION Note.6

9~12V

RATEDCURRENT

3.8A

CURRENTRANGE

0~3.8A

RATEDPOWER

45.6W

RIPPLE&NOISENOTE.2

2VP-P

VOLTAGE ADJ RANGE

11.5~13V

Can be adjusted by internal potential meter SVR1

CURRENT ADJ. RANGE Note.5

3% ~  -25%. Can be adjusted by internal potential meter SVR2

VOLTAGETOLERANCENOTE.3

±10%

LINEREGULATION

±3.0%

LOADREGULATION

±5.0%

SETUP TIME

1500ms / 230VAC    3000ms / 115VAC at full load

INPUT

VOLTAGERANGE

90~264VAC 127~370VDC

FREQUENCYRANGE

47~63HZ

EFFICIENCY

83.5%

VOLTAGE RANGE

PF≥ 0.9 at 75 ~ 100%  load, 115VAC / 230VAC

AC CURRENT

0.55A/115VAC     0.25A/230VAC

INRUSH CURRENT

40A/230VAC

LEAKAGECURRENT

<0.75mA / 240VAC

PROTECTION

OVER CURRENT

95 ~110%

Protection typeConstant current limiting,recovers automatically after fault condition is removed

SHORT CIRCUIT

Hiccup mode, recovers automatically after fault condition is removed.

OVER VOLTAGE

13.8~16V

Protection typeShut down o/p voltage,re-power on to recover.

OVER TEMPERATURE

95± 10 (TSW1) detect on heatsink of power transistor

Protection type : Shut down o/p voltage, recovers automatically after temperature goes down

ENVIRONMENT

WORKINGTIMP

-30~+50(refer to output load derating curve)

WORKINGHUMIDITY

-20~95%Rhnon-condensing

STORAGE TEMP HUMIDITY

-40~+80 10~95%RH

TEMPCOEFFICIENT

±0.03%(0~50)

VIBRATION

10~500HZ,2G10min/1cycle period for 60 min each alongX,Y,Zaxes

SAFETY&EMC

SAFETYSTANDARDS

UL1310 Class 2, TUV EN61347-1, EN61347-2-13, CAN/CSA C22.2 No. 223-M91(except for 48V), IP64 approved

WITHSTAND VOLTAGE

I/P-O/P:3.75KVAC     I/P-FG:1.88KVAC     O/P-FG:0.5KVAC

ISOLATIONRESISTANCE

1/P-0/P:>100M Ohms/500VDC/25/70%RH

EMI CONDUCTICN&

RADIATION

Compliance to EN55015

HARMONICCURRENT

Compliance to EN61000-3-2 Class C (>80% load), Class D (>50% load) ; EN61000-3-3

EMS IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, EN61547, light industry level,  criteria A

QTHERS

MTBF

497.8Khrs min MIL-HDBK-217F(25)

DIMENSION

181*61.5*35mm(L*W*H)

PACKING

0.5Kg; 24pcs/13Kg/0.75CUFT

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

Direct connecting to LEDs is not suggested for models with .RIPPLE & NOISE.  > 10% and using additional drivers is highly recommended.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Please refer to OLP characteristics.

5. Derating may be needed under low input voltage. Please check the derating curve for more details.

6. Output voltage can be adjusted through the SVR1 on the PCB ; limit of output constant current level can be adjusted through the SVR2 on the PCB.

7. Constant current operation region is within 75% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please

reconfirm special electrical requirements for some specific system design.

8. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the

complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.